Widras Book of Instructions

  Bike Mount Holder

Features: Multiple Function and locations: This mount can be mounted on various of locations such as bike handle bars, shopping Cart, office desks, baby carriage with 360 degrees rotation holder.

Quick Installation:
1.Open the clip and place the rubber into the handle.
2.Attach the support to bike handle by unscrew the clip and fastened the handle.
3.Stretch and work the rubber band over the clip handle.
4.Connect the clip and the support together. Twist the screw cap until tight.
5.Install your phone into the mount.
6.Stretch the rubber band's corners over your mobile device's corners.

Compatible with the most devices: Maximum recommended Wide 3.5 Inches, the Bike Mount let's you enjoy the ride without worrying about you cellphone.

Two elastic bands : that goes behind your phone for each corner to secure your phone for ride.

ATTENTION : The Nut of the Pivot can be Tightened to keep the grip securely in position.

Warranty: This product comes with a Lifetime Limited Warranty.Please avoid purchasing the product from unauthorized sellers. During the warranty period, Widras  will replace without charge, a Materially Defective Product. Widras will also return replacement Products to you in working condition.

 Magnetic Air Vent Car Mount

Instructions to setup Installation:
1.Easily place the mount into any one of your car's air vents.
2.Place the magnet metal plate in your case between the cover and the phone, Or stick on the round magnet metal on your phone or GPS.
3.Bring the device close to the mount and it will take it easily.

Compatibility: ALL smartphones, tablets, cell phones, MP3 and GPS. iPhone 7/6s /6s/6/5S/5C/5/4S, Galaxy S7/S7 Edge, S6/S6 Edge/S6 Edge+, S5, Galaxy Note 5/4, Moto X, Moto G, LG G4, Google Nexus 5/4, Nokia Lumia, Sony Xperia, HTC One M9M8 M7 and GoPro.

Notice: Four metal plates are included with the car mount, two rectangular plates inside the package and two round plates
Please remove the metal disc from the front of the magnetic mount before using. Some phone cases may not work well with the car mount. Cases with rounded, thick or unsmooth backs (e.g. Otter boxes) may not make using this car mount difficult.

Warranty: This product comes with a Lifetime Limited Warranty. Please avoid purchasing the product from unauthorized sellers. During the warranty period, Widras  will replace without charge, a Materially Defective Product. Widras will also return replacement Products to you in working condition.

✔ATTENTION : This Car Mount is not compatible with Samsung S7 Quick Charger. 

 

One Click Car Mount

FeaturesMultiple Function and locations: This mount can be mounted on various of locations in your car with 360 degrees rotation holder. It's fast and easy to install on any types of material, even leather.

Compatible with the most devices: Maximum recommended Wide 3.4 Inches, the Car Mount let's you enjoy the road without worrying about you cellphone.

✔Instructions to setup Installation:
1. Clean the area on the windshield or dashboard you would like to place your mount.
2. Place your mount on the dashboard/windshield and by pressing lightly on the mount close the mount.
3. Attach to the swivel ball the One Click mechanism, and twist the screw cap until tight.
4. Place your phone on the mount by simple pushing the phone in, it will automatically close and lock your phone.

✔Warranty: This product comes with a Lifetime Limited Warranty. Please avoid purchasing the product from unauthorized sellers. During the warranty period, Widras  will replace without charge, a Materially Defective Product. Widras will also return replacement Products to you in working condition.

Notice: No extra tools for installation needed. Removing your device is made very easy also.

Windshield & Air Vent Magnetic Car Mount


✔Instructions to setup Installation:
1.Pick between Windshield or Air Vent Mount.
2.For Windshield Prepare the location on the windshield before you stick it, by cleaning the glass with an alcohol pad and make sure it is dry before applying it. Place the mount in the location you desire and press the click. Suction procedure will make your device to stay strong and easy adjustable. For Air Vent Mount pull the spring and insert the Hook inside the Air Vent location and release the spring to lock the Mount.
3.Place the magnet metal plate in your case between the cover and the phone, Or stick on the round magnet metal on your phone or GPS.
4.Bring the device close to the mount and it will take it easily.

Compatibility:ALL smartphones, tablets, cell phones, MP3 or GPS.

Notice:Two metal plates are included with the car mount, 1 rectangular plate inside the package and 1 round plate. Please remove the metal disc from the front of the magnetic mount before using.

✔Warranty: This product comes with a Lifetime Limited Warranty. Please avoid purchasing the product from unauthorized sellers. During the warranty period, Widras  will replace without charge, a Materially Defective Product. Widras will also return replacement Products to you in working condition.

 

 

Steel Car Magnetic Dash Board Cell Phone Holder

 

 

Features:

The Magnetic Mount for smartphones is very easy to install and occupies very little space in your car or desk. It's the biggest advantage is the ease with which you attach and detach your cell phone to the mount because of magnetic technology.Using your phone while attached to the mount is very easy. It can easily rotate, adjust, or tilt to any angle that best fits the view of your phone.

Compatibility:
ALL smartphones, tablets, cell phones, MP3 or GPS.

Installation:
Dash Ball Mount should be installed in warm Temperature: 60°F(16°C)

Metal pads Installation Instructions:

a.Stick anti-scratch protection films on your device or case in same place where the metal pad disc will be installed.

b.The Metal pad discs can be installed directly on the back of the phone or case. Also metal pads can be installed under the case of your device.

c.Remove the adhesive backing from the metallic pad.

d.Install the pad in the center of the back of your device and firmly press into place.

e. You can install 2 metal pads on the same device to cover more surface.

Dash Ball Mount Installation Instructions:

a.Before removing the adhesive backing, PLEASE test the position of the mount you like.

b.Clean the chosen area with the alcohol pad included in the package and wait until it dries.

c.Peel the adhesive from the Dash Ball Mount backing and press firmly for 10 seconds in place

d.Please allow 24 hours for the mount to stick to the place, before installing Magnetic Disc and attaching your device.

Notice:Mount can be installed in any position horizontal and vertical, on smooth surface such as plastic, wood or glass!

Please remove the metal disc from the front of the magnetic mount before using.

Warranty: This product comes with a Lifetime Limited Warranty. Please avoid purchasing the product from unauthorized sellers. During the warranty period, Widras  will replace without charge, a Materially Defective Product. Widras will also return replacement Products to you in working condition.

Box Included Items:

Magnetic Disc (1)

Dash Ball Metal Mount (1)

Large Size Metal Pads (2)

Small Size Metal Pads (2)

3M VHB Adhesive (10)

Cleaning Wipes (2)

 

Steel Magnetic Dashboard Car Mount & Office Desk Stand

Features:

This Magnetic Mount for smartphones is very easy to install and occupies very little space in your car but the biggest advantage is the ease with which you attach and detach your cell phone to the mount.Using your phone while attached to the mount is very easy. It can easily rotate, adjust, or tilt to any angle that best fits the view of your phone
Installation:Dash Ball Mount should be installed in warm Temperature: 60°F(16°C)

Metal pads Installation Instructions:

a.Stick anti-scratch protection films on your device or case in same place where the metal pad disc will be installed.

b.The Metal pad discs can be installed directly on the back of the phone or case. Also metal pads can be installed under the case of your device.

c.Remove the adhesive backing from the metallic pad.

d.Install the pad in the center of the back of your device and firmly press into place.

e. You can install 2 metal pads on the same device to cover more surface.

Dash Ball Mount Installation Instructions:

a.Before removing the adhesive backing, PLEASE test the position of the mount you like.

b.Clean the chosen area with the alcohol pad included in the package and wait until it dries.

c.Peel the adhesive from the Dash Ball Mount backing and press firmly for 10 seconds in place

d.Please allow 24 hours for the mount to stick to the place, before installing Magnetic Disc and attaching your device.

Notice:Mount should be installed only in horizontal position and only on hard, smooth surface such as plastic, wood or glass!

 Please remove the metal disc from the front of the magnetic mount before using.

Warranty: This product comes with a Lifetime Limited Warranty. Please avoid purchasing the product from unauthorized sellers. During the warranty period, Widras  will replace without charge, a Materially Defective Product. Widras will also return replacement Products to you in working condition.

Box Included Items:

Dash Ball Mount (1)

Magnetic Disc (1)

Large Size Metal Pads (2)

Small Size Metal Pads (2)

3M VHB Adhesive Bands (10)

Cleaning Wipes (2)